[meteorite-list] wire saw cost
From: Shawn Alan <photophlow_at_meteoritecentral.com>
Date: Thu, 10 Mar 2011 16:33:04 -0800 (PST) Message-ID: <798339.57246.qm_at_web35408.mail.mud.yahoo.com> Matt, Gary, and Listers, ? What would be the best way to go for irons slices if you had lets say Tucson iron and I have seen that go for $1000 a gram or lets say you have a 10gram Compo and you want to make 200mg slices, what method would be the best for that, not saying cutting up Compos to the size is cost effective? ? ?Shawn Alan IMCA 1633 eBaystore http://shop.ebay.com/photophlow/m.html [meteorite-list] wire saw cost mail at mhmeteorites.com mail at mhmeteorites.com Thu Mar 10 18:34:44 EST 2011 Previous message: [meteorite-list] wire saw cost Next message: [meteorite-list] wire saw cost Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] -------------------------------------------------------------------------------- As a general rule of thumb, material 30.00/g or higher, may be best cut on a wire saw. This is could be an OC. Probably not an iron. Of course pallasites look great thin cut too. Matt ------------------------ Matt Morgan Mile High Meteorites http://www.mhmeteorites.com P.O. Box 151293 Lakewood, CO 80215 -----Original Message----- From: Gary Fujihara <fujmon at mac.com> Sender: meteorite-list-bounces at meteoritecentral.com Date: Thu, 10 Mar 2011 13:32:16 To: Andr?? Moutinho<moutinho at bol.com.br> Cc: <meteorite-list at meteoritecentral.com> Subject: Re: [meteorite-list] wire saw cost Aloha Andre, Depending on the cost of the material, it may or may not be more cost effective to use a wire saw. A wire saw is better for planetaries or other expensive or rare meteorites, where cost of material is high, and so minimizing cut loss is imperative. If the material is cheap, then the expense of using a wire saw is not justified for minimizing cut loss because you would spend more money on cutting it than you would saving on reduced cut loss. You have to balance the cost of cutting with expected cut loss . For example, a friend cut a cheap CV3 on a wire, and cost him big money to do so. He would have been better off taking the cut loss on a lap saw for a cheaper cutting expense. gary On Mar 10, 2011, at 12:59 PM, Andr? Moutinho wrote: > Hello, > > Does anyone can give me an idea of cutting cost using a wire saw to cut a 300g ordinary chondrite into 3mm slices? > > Thanks! > Andre >______________________________________________ > Visit the Archives at http://www.meteoritecentral.com/mailing-list-archives.html > Meteorite-list mailing list > Meteorite-list at meteoritecentral.com > http://six.pairlist.net/mailman/listinfo/meteorite-list Gary Fujihara Big Kahuna Meteorites (IMCA#1693) 105 Puhili Place, Hilo, Hawai'i 96720 http://bigkahuna-meteorites.com/ http://shop.ebay.com/fujmon/m.html (808) 640-9161 ______________________________________________ Visit the Archives at http://www.meteoritecentral.com/mailing-list-archives.html Meteorite-list mailing list Meteorite-list at meteoritecentral.com http://six.pairlist.net/mailman/listinfo/meteorite-list -------------------------------------------------------------------------------- Previous message: [meteorite-list] wire saw cost Next message: [meteorite-list] wire saw cost Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] -------------------------------------------------------------------------------- More information about the Meteorite-list mailing list Received on Thu 10 Mar 2011 07:33:04 PM PST |
StumbleUpon del.icio.us Yahoo MyWeb |